Gulley Performance Center

2604 Fort Henry Dr. Kingsport, TN. 37664
Call for information 423-247-2271


Spoons


Martin Auto Body Spoons are drop forged out tool steel and heat treated for lasting strength. Spoons are available in a variety of shapes and crowns. They can be used for hammer dinging in finishing and slapping panels. Can also be used for prying or as a dolly behind brackets, inner panels, and other close places. Spoons are made in Fort Worth, Texas USA.


SURFACING SPOON

Excellent spoon for fender spring hammering, finishing and shaping. Curve gets behind inner construction between panels that are close for removal of dents. Molds panels. Blade fully polished. 9″ Blade Length. 218″ Width. Overall Length 1518″.

Weight 2.5 lbs.

1024 $37.00

image of dinging hammer


MEDIUM CROWN SPOON

Long slender shape just like the 1024 surfacing spoon. Inside with medium crown, for high ridges or prying. For slapping and surface finishing on fenders, panels and trunk lids. Blade fully polished. 9″ Blade Length. 218″ Width. Overall Length 1478″.

Weight 1.5 lbs.

1026 $37.00

image of dinging hammer


LIGHT DINGING SPOON

To ding ridges smooth and level. When held against ridge and struck with hammer, spreads blow over large area making smooth job and preventing damage to metal or finish. Not made for prying. Length 10″ overall. Face 2″ 4516″.

Weight .50 lbs.

1036 $27.00

image of dinging hammer


HEAVY DUTY DOUBLE END S-SPOON

General purpose fender and frame spoon. Designed to provide further reach on panels and behind reinforcements. Prying, heavy duty design for use on SUV frames. 12316″ Length. 138 X 514″ Face.

Weight 3.0 lbs.

1044 $69.00

image of dinging hammer


COMBINATION SPOON

General purpose fender spoon. Used as dolly behind brackets, inner panels and similar places. Handle offset to give balance when dinging and for long reach. Has high-crown working surface. Face 134″ 512″. Handle 1″ octagon 434″ long.

Weight 3.0 lbs.

1050 $49.00

image of dinging hammer


SPOON DOLLY

Long handle permits many uses in places otherwise inaccessible. Can be driven between reinforcements and outer panel, then used to pry outward as the metal is dinged. Excellent forming and caulking tool for the deep pockets of doors, quarter-panels, rear fenders and lower trunk panels. Size 212″ 1″ 3″.

Weight 4.2 lbs.

1052 $50.00

image of dinging hammer


LONG CURVED SPOON

Long, thin, curved blade is handy for prying up dents behind curved reinforcements in header panels, hinge anchors in doors, body pillars and reinforcements in hoods and radiator shells. Length 1012″ overall. Face 2″ 7″.

Weight 1.5 lbs.

1054 $37.00

image of dinging hammer


WING-DING SPOON DOLLY

The answer to repair problems on high fins. A dolly, a spoon, a pry. Long handle and special contours for working up inside cramped fins. Wide spoon transmits hammer blows over wide area without damaging finish. 1″ handle diameter, 19″ overall length. Weight 4.5 lbs.

1056 $66.00

image of dinging hammer


HEAVY DUTY DRIVING AND FENDER BENDING TOOL

Useful for restoration of turned under, non-wired flanged edges. Also handy for alignment of inner construction and flanges on alligator hoods. Heavy formed striking pads. Length 1418″.

Weight 3.2 lbs.

1091 $78.00

image of dinging hammer


CAULKING IRON

Excellent precision made wire caulking iron. Polished working surfaces are rounded for use on inside moldings. Face 134″ 1″. Overall length 11″.

Weight 1.4 lbs.

1096C $39.00

image of dinging hammer